Search from various English teachers...
Spain flagToni Espinosa
DIY mini centrifuge Hello. Could someone help me with that text? Thanks very much! :-) ------------------------- Now I am working in a DIY mini centrifuge. For that project I am using a hard disk motor. That motors are brushless, so they produce few friction and can reach higger speed than standard motors, furthermore, it is very easy to recycle them from old hard disks. I am making the centrifuge enclosure with layers of Wood. I had carved each layer, with different shapes, in order to make space to put all electronics inside. You can see that in the pictures. The centrifuge is going to be controlled by an Arduino micro controler. I am going to use an infrared sensor to count how fast the motor spines. I have an old lab centrifue which I bought in a second hand market. I putted a tachometer, based on arduino too, into that aparatus. Then, I realized that the centrifuge speed tended to change progressively. It hadn't a very stable speed. In this mini centrifuge, arduino is going to be able to ajust the engine speed if that differs from the programed one. I am using a special electronic component named "Electronic speed control", ESC in short, which is used for control drone or helicopter motors which are brushless too. That device allows the arduino controlling the motor easily. Using a little screen and three buttons will be possible program speed and time of working of the centrifuge.

Corrections · 5

1
In this mini centrifuge, Arduino is going to be able to ajust the engine speed if that it differs from the programmed one speed. I am using a special electronic component named called an "Electronic speed control", ESC in for short, which is used for to control drone or helicopter motors which are brushless too. That device allows the Arduino to controlling the motor easily.

Using a little (better: small) screen and three buttons, it will be possible to program the speed and run time of working of the centrifuge.
1

DIY mini centrifuge

Hello.
Could someone help me with that text?

Thanks very much! :-)
-------------------------


Now I am working on a DIY mini centrifuge.

For this project I use a hard disk motor. This motor is brushless, so it produces little friction and can reach higher speeds than standard motors. Ffurthermore, it is very easy to recycle one from an old hard disk.

I make the centrifuge enclosure with layers of Wood. I carved out different shapes to make space for the electronic components inside, as shown in the picture.

The centrifuge will be controlled by an Arduino micro controller. I will use an infrared sensor to count how fast the motor spins.

I have an old lab centrifuge which I bought in a second hand market. I put a tachometer, based also on an arduino, into that apparatus. Then, I realized that the centrifuge speed tended to change progressively. Its speed was unstable.

In this mini centrifuge, the arduino will hopefully regulate the engine speed if that differs from the speed set by the arduino. I use a special electronic component: "Electronic Sspeed Ccontrol", or ESC, which is used to control brushless drone or helicopter motors, too. That device allows the arduino to control the motor easily.

Using a little screen and three buttons, it will be possible to program the speed and time of working of the centrifuge.

Very ingenious and well written!

1

DIY mini centrifuge

Now I am currently working on a DIY mini centrifuge.

For this project I am using a hard disk motor. These motors are brushless, so they produce few little friction and can reach higher speeds than standard motors. Furthermore, it is very easy to recycle them from old hard disks.

I am making the centrifuge enclosure with layers of wood. I had carved each layer, with different shapes, in order to make space to put all the electronics inside. You can see this in the pictures.

The centrifuge is going to be controlled by an Arduino microcontroller. I am going to use an infrared sensor to count how fast the motor spines.

I have an old lab centrifuge which I bought in a second hand market. I putted a tachometer, also based on Arduino too, into that apparatus. Then, I realized that the centrifuge speed tended to change progressively. It hadn't a very stable speed. Its speed wasn't very stable.


Want to progress faster?

Join this learning community and try out free exercises!

Don’t miss out on the opportunity to learn a language from the comfort of your own home. Browse our selection of experienced language tutors and enroll in your first lesson now!

Start Learning Today